Mechatronics Modelling and Control

Assessed Matlab Practical 3 – Control of robotic arm Aim: To control the pitch attitude of a robotic arm.

To turn the robotic arm, a servo actuator motor is used to apply Torque, T that will rotate the robotic arm.

The angular position of the robotic arm is govern by the.

T ??J

d2?

dt2

??B d?

dt

Where ??is the robotic arm angular positon, J is the moment of inertia of the robotic arm and B is the coefficient of damping primarily due to friction in the gears. T is the torque applied to move the robotic arm.

1. Show that if the output is angular velocity (?). The equation that models the movement of the antenna is a first order differential equation. What is the gain, Ka and time constant Ta? Hence write down the Transfer Function, ?(s)/T(s).

2. Enter the transfer function ?(s)/T(s) into Matlab and use the LTIview facility to plot a time response of the robotic arm when a constant torque (T = 10Nm) is applied assuming angular velocity, ? as the output in deg/s. What is the steady state velocity? What is the 95% settling time?

30%

3. The robotic arm is controlled via a motor which adjust the Torque as the robotic arm turns to a desired angle.

A 0-10v volts control signal is used to drive the motor and turn the robotic arm between angles of 0 to 90°. The diagram bellow shows the transfer function of the motor and the robotic arm.

Hence determine the value of the encoder gain Kc, if the input voltage range from 0 to 10V correspond to the output angles ranging from 0 to 90°. Use block manipulation and LTI viewer to measure the percentage overshoot and tmax of the control loop assuming a step input u of 5V.

What is the position of the robotic arm assuming this step input?

Hence determine the value of the encoder gain Kc, if the input voltage range from 0 to 10V correspond to th

20%

4. Hence determine the undamped natural frequency and damping constant for a 5V input.

5. Determine the closed loop transfer function of the robotic arm motor control loop.

40%

J = 0.314 N.m.s^2/deg

B = 0.039 N.m.s/deg

Kt = 0.343 N.m/A

Kv = 0.035 V.s/deg

Question 1

Value for Ka =

Value for Ta =

Question 2

- ?ss = deg/s

- t95% = /sec

Question 3

Kc =

tmax = /sec

??????????deg

% overshoot =

Question 4

K =

?n

Undamped natural frequency =

Question 5

S2 S1 S0

Num coeff

Deno coeff

Conclusion

Which of the following statements are true or false?

1. Increasing the rate gyro gain can remove overshoot from the system.

2. Increasing the encoder gain can decrease the position range of the robotic arm.

3. Induction motor is suitable for controlling the position of the robotic arm.

4. Increasing the signal voltage decreases the angular velocity of the robotic arm

5. Increasing the torque gain can increase the overshoot.

Assessed Matlab Practical 3 – Control of robotic arm Aim: To control the pitch attitude of a robotic arm.

To turn the robotic arm, a servo actuator motor is used to apply Torque, T that will rotate the robotic arm.

The angular position of the robotic arm is govern by the.

T ??J

d2?

dt2

??B d?

dt

Where ??is the robotic arm angular positon, J is the moment of inertia of the robotic arm and B is the coefficient of damping primarily due to friction in the gears. T is the torque applied to move the robotic arm.

1. Show that if the output is angular velocity (?). The equation that models the movement of the antenna is a first order differential equation. What is the gain, Ka and time constant Ta? Hence write down the Transfer Function, ?(s)/T(s).

2. Enter the transfer function ?(s)/T(s) into Matlab and use the LTIview facility to plot a time response of the robotic arm when a constant torque (T = 10Nm) is applied assuming angular velocity, ? as the output in deg/s. What is the steady state velocity? What is the 95% settling time?

30%

3. The robotic arm is controlled via a motor which adjust the Torque as the robotic arm turns to a desired angle.

A 0-10v volts control signal is used to drive the motor and turn the robotic arm between angles of 0 to 90°. The diagram bellow shows the transfer function of the motor and the robotic arm.

Hence determine the value of the encoder gain Kc, if the input voltage range from 0 to 10V correspond to the output angles ranging from 0 to 90°. Use block manipulation and LTI viewer to measure the percentage overshoot and tmax of the control loop assuming a step input u of 5V.

What is the position of the robotic arm assuming this step input?

Hence determine the value of the encoder gain Kc, if the input voltage range from 0 to 10V correspond to th

20%

4. Hence determine the undamped natural frequency and damping constant for a 5V input.

5. Determine the closed loop transfer function of the robotic arm motor control loop.

40%

J = 0.314 N.m.s^2/deg

B = 0.039 N.m.s/deg

Kt = 0.343 N.m/A

Kv = 0.035 V.s/deg

Question 1

Value for Ka =

Value for Ta =

Question 2

- ?ss = deg/s

- t95% = /sec

Question 3

Kc =

tmax = /sec

??????????deg

% overshoot =

Question 4

K =

?n

Undamped natural frequency =

Question 5

S2 S1 S0

Num coeff

Deno coeff

Conclusion

Which of the following statements are true or false?

1. Increasing the rate gyro gain can remove overshoot from the system.

2. Increasing the encoder gain can decrease the position range of the robotic arm.

3. Induction motor is suitable for controlling the position of the robotic arm.

4. Increasing the signal voltage decreases the angular velocity of the robotic arm

5. Increasing the torque gain can increase the overshoot.

Assessment 3ASSESSMENTThis module is assessed through a portfolio submission which comprises 70% of individual coursework and 30% of a group presentation. The group members are expected to work together...powerpointwill need discussion to startENGINEERING DESIGN FOR INNOVATIONASSESSMENT BRIEF | 1CWK100This is an assignment for students on the following postgraduate programmes:• MSc Engineering Smart Systems•...2.2.2 Formative 1Week 7 Find a gap in practice for evidence translation - Formative Assessment 1Introduction to the Formative assessment Upon completing this lesson, you should be able to: • Find a knowledge...Global Business Environment Deadline: 29th October 2021Assessment GuidelinesWord Count: 500 (+-10%)Scenario:You are to select a UK company and conduct a PESTEL analysis on the firms operating environment...Assessment: Individual portfolio up to 4000 words or equivalent This assignment is to develop either a brand brief for a new brand OR a brand audit and recommendations for a failing brand. The portfolio...Assessment: Individual Coursework Assessment methods which enable students to demonstrate the learning outcomes for the module: Weighting: Learning Outcomes demonstrated Individual Coursework (3,000 words...Dissertation (All chapters) - Indicative table of contents provided in the brief.Topic - ESG investing and portfolio perfomancePlease refer to the brief attached for more information.Total word count -...**Show All Questions**